View M52755FP_88820.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH DESCRIPTION
The M52755FP is a semiconductor integrated circuit for the RGBHV interface. The device features switching signals input from two types of image sources and outputting the signals to the CRT display, etc. Synchronous signals, meeting a frequency band of 10kHz to 200kHz, are output at TTL. The frequency band of video signals is 250MHz, acquiring high-resolution images, and are optimum as an interface IC with high-resolution CRT display and various new media.
VCC1 (R) 1 INPUT1 (R) 2 VCC1 (G) 3 NC 4 INPUT1 (G) 5 VCC1 (B) 6 INPUT1 (B) 7 36 Vcc2 (R) 35 OUTPUT (R) 34 GND 33 NC 32 NC 31 Vcc2 (G) 30 OUTPUT (G) 29 GND 28 Vcc2 (B) 27 OUTPUT (B) 26 GND 25 OUTPUT (for sync on G) 24 VCC 23 NC 22 OUTPUT (H) 21 OUTPUT (V) 20 GND 19 SWITCH
PIN CONFIGURATION (TOP VIEW)
FEATURES
INPUT1 (H) 8 INPUT1 (V) 9 GND 10 INPUT2 (R) 11 GND 12 INPUT2 (G) 13
M52755FP
*
* *
Frequency band: RGB......................................................250MHz HV.............................................10Hz to 200kHz Input level:RGB.........................................................0.7V P-P (typ.) HV TTL input.............................3.5VO-P (both channel) Only the G channel is provided with sync-on video output. The TTL format is adopted for HV output.
APPLICATION
Display monitor
NC 14 GND 15 INPUT2 (B) 16
RECOMMENDED OPERATING CONDITION
Supply voltage range........................................................4.5 to 5.5V Rated supply voltage..................................................................5.0V
INPUT2 (H) 17 INPUT2 (V) 18
Outline 36P2R-A
NC : NO CONNECTION
BLOCK DIAGRAM
OUTPUT (R) Vcc2 (R) GND 36 35 34
NC 33
OUTPUT OUTPUT (B) (for sync on G) Vcc2 (G) GND VCC OUTPUT (G) Vcc2 (B) NC GND 32 31 30 29 28 27 26 25 24
NC 23
OUTPUT (V) SWITCH OUTPUT (H) GND 22 21 20 19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
NC NC INPUT1 (H) GND INPUT1 (R) VCC1 (B) GND INPUT2 (G) INPUT1 (V) INPUT1 (G) INPUT1 (B) VCC1 (R) INPUT2 (R) VCC1 (G)
INPUT2 (B) INPUT2 (V) GND INPUT2 (H)
1
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH ABSOLUTE MAXIMUM RATINGS (Ta=25C)
Symbol VCC Pd Topr Tstg Vopr Vopr' Surge Parameter Supply voltage Power dissipation Ambient temperature Storage temperature Recommended supply voltage Recommended supply voltage range Electrostatic discharge Ratings 7.0 1603 -20 to +85 -40 to +150 5.0 4.5 to 5.5 200 Unit V mW C C V V V
ELECTRICAL CHARACTERISTICS (VCC=5V, Ta=25C, unless otherwise noted)
Test conditions Symbol Parameter VCC Test point (V) (s) VCC A A 5 5 Input SW Min. 46 46 Limits Unit Typ. 66 66 Max. 86 86 mA mA
SW2 SW4 SW6 SW7 SW8 SW10 SW12 SW14 SW15 SW16 SW17 Rin1 Gin1 Bin1 Hin1 Vin1 Rin2 Gin2 Bin2 Hin2 Vin2 Switch
ICC1 ICC2 (RGB SW) VDC1 VDC2 VDC3 VDC4 Vimax1 Vimax2 GV1 GV1 GV2 GV2 GV3 GV4 FC1 FC1 FC2 FC2 FC3 FC4
Circuit current1 (no signal) Circuit current2 (no signal)
b - b - b - b - b - b -
b - b - b - b - b - b -
b - b - b - b - b - b -
b - b - b - b - b - b - b - b - b -
b - b - b - b - b - b - b -
b - b - b - b - b - b - b -
b - b - b - b - b - b - b -
b - b - b - b - b - b - b -
b - b - b - b - b - b - b -
b b - GND b a - OPEN b b - GND b - a
OPEN
Output DC voltage1 Output DC voltage2 Output DC voltage3 Output DC voltage4 Maximum allowable input1 Maximum allowable input2 Voltage gain1 Relative voltage gain1 Voltage gain2 Relative voltage gain2 Voltage gain3 Voltage gain4 Freq. characteristic1 (100MHz)
Relative Freq. characteristic1 (100MHz)
T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.23 T.P.23 T.P.2 T.P.4 T.P.6 T.P.10 T.P.12 T.P.14 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25
5 5 5 5 5 5 5
1.85 1.85 0.75 0.75 2.0 2.0 0.3 -0.4
2.05 2.05 1.15 1.15 2.4 2.4 0.9 0 0.9 0 0.2 0.2 0 0 0 0 -1.5 -1.5
2.25 2.25 1.55 1.55 - - 1.5 0.4 1.5 0.4 0.8 0.8 1.0 1.0 1.0 1.0 1.0 1.0
V V V V VP-P VP-P dB dB dB dB dB dB dB dB dB dB dB dB
b b - GND b - a
OPEN
abb bab bba
SG1 SG1 SG1
b b - GND b - a
OPEN
b -
b -
b -
b abb bab bba b - SG1 SG1 SG1 - b - b - b - b - b -
abb bab bba
SG2 SG2 SG2
b b - GND
Relative to measured values above 5 b - b - b - b - b abb bab bba b - SG2 SG2 SG2 - b - b - b - b - a
OPEN
0.3 -0.4
T.P.23 T.P.23 T.P.31 T.P.28 T.P.25
5 5 5
Relative to measured values above b b b b b b b a - - - - - - SG2 - b b b b b b b a - - - - - - SG2 - abb bab bba
SG4 SG4 SG4
b b - GND b a - OPEN b b - GND
-0.4 -0.4 -1.0 -1.0
b -
b -
b -
b -
b -
Relative to measured values above
T.P.31 T.P.28 T.P.25
Freq. characteristic2 (100MHz)
Relative Freq. characteristic2 (100MHz)
5
b -
b -
b -
b -
b abb bab bba b - SG4 SG4 SG4 -
b -
a
OPEN
-1.0 -1.0
Relative to measured values above
T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25
Freq. characteristic3 (250MHz) Freq. characteristic4 (250MHz)
5 5
abb bab bba
SG5 SG5 SG5
b - b -
b -
b -
b -
b -
b -
b b - GND b - a
OPEN
-3.0 -3.0
b -
b -
b -
b abb bab bba b - SG5 SG5 SG5 -
2
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH
ELECTRICAL CHARACTERISTICS (cont.)
Test conditions Symbol Parameter VCC Test point (V) (s) VCC
T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25 T.P.31 T.P.28 T.P.25
Input
SW Min. - - - - - - - - - - - -
Limits Unit Typ. -60 Max. -50 dB
SW2 SW4 SW6 SW7 SW8 SW10 SW12 SW14 SW15 SW16 SW17 Rin1 Gin1 Bin1 Hin1 Vin1 Rin2 Gin2 Bin2 Hin2 Vin2 Switch
C.T.I.1
Crosstalk between two inputs1 (10MHz) Crosstalk between two inputs2 (10MHz) Crosstalk between two inputs3 (100MHz) Crosstalk between two inputs4 (100MHz) Crosstalk between channels1 (10MHz) Crosstalk between channels2 (10MHz) Crosstalk between channels3 (100MHz) Crosstalk between channels4 (100MHz)
5
abb bab bba
SG3 SG3 SG3
b - b - b - b - b - b - b - b - b - b - b - b -
b -
b -
b -
b -
b -
b GND -
OPEN
C.T.I.2
5
b -
b -
b -
b abb bab bba b - SG3 SG3 SG3 - b - b - b - b - b -
b GND -
OPEN
-60
-50
dB
C.T.I.3
5
abb bab bba
SG4 SG4 SG4
b GND -
OPEN
-40
-35
dB
C.T.I.4
5
b -
b -
b -
b abb bab bba b - SG4 SG4 SG4 - b - b - b - b - b -
b GND -
OPEN
-40
-35
dB
C.T.C.1 C.T.C.2 C.T.C.3 C.T.C.4 Tr1
5 5 5 5 5 5 5 5
abb bab bba
SG3 SG3 SG3
b b - GND b - a
OPEN
-50 -50 -30 -30 1.6 1.6 1.6 1.6
-40 -40 -25 -25 2.5 2.5 2.5 2.5
dB dB dB dB nsec nsec nsec nsec
b -
b -
b -
b abb bab bba b - SG3 SG3 SG3 - b - b - b - b - b -
abb bab bba
SG4 SG4 SG4
b b - GND b - a
OPEN
b - a a b - b - b - b - b - b - b - b - b - b - b - b -
b - a a b - b - b - b - b - b - b - b - b - b - b - b -
b - a a b - b -
b abb bab bba b - SG4 SG4 SG4 - b - b - b - b - b - b - b - b - b - b -
SG6 SG6 SG6
b b - GND b b - GND b - b - a
OPEN
Pulse characteristic1 Tf1 Tr2 Pulse characteristic2 Tf2 (HV SW) VoH1 VoH2 VoL1 VoL2 Vith1 Vith2 Trd1 Trd2 Tfd1 Tfd2 Vsth1 Vsth2 High level output voltage1 High level output voltage2 Low level output voltage1 Low level output voltage2 Input selectional voltage1 Input selectional voltage2 Rising delay time1 Rising delay time2 Falling delay time1 Falling delay time2 Switching selectional voltage1 Switching selectional voltage2
SG6 SG6 SG6
b b a a a - SG6 SG6 SG6 - b b a a a - SG6 SG6 SG6 - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b - b -
a
OPEN
T.P.19 T.P.20 T.P.19 T.P.20 T.P.19 T.P.20 T.P.19 T.P.20 T.P.7 T.P.8 T.P.15 T.P.16 T.P.19 T.P.20 T.P.19 T.P.20 T.P.19 T.P.20 T.P.19 T.P.20 T.P.17 T.P.17
5 5 5 5 5 5 5 5 5 5 5 5
b - b a a a a a SG1 SG1 SG1 SG7 SG7 - b - b - b - b -
b c c - 5.0V 5.0V b b b - - - b c c - 0V 0V b b b - - - b c c - Variable Variable b b b - - - b a a - SG7 SG7 b b b - - - b a a - SG7 SG7 b b b - - -
b c - 5.0V 5.0V OPEN b b b b - - - GND b c c a - 0V 0V OPEN b b b b - - - GND a b c c - Variable Variable OPEN b b b b - - - GND a b a a - SG7 SG7 OPEN b b b b - - - GND a b a a - SG7 SG7 OPEN b b b c - - - c
b b - GND a c
4.5 4.5 - - 2.0 2.0 - - - - 0.5 0.5
5.0 5.0 0.2 0.2 2.5 2.5 100 100 50 50 1.5 1.5
- - 0.5 0.5 3.0 3.0 150 150 100 100 2.0 2.0
V V V V V V nsec nsec nsec nsec V V
b a a a a a - SG1 SG1 SG1 SG7 SG7
3
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH ELECTRICAL CHARACTERISTICS TEST METHOD
It omits the SW.No accorded with signal input pin because it is already written in Table. SW A, SW1, SW3, SW5 is in side a if there is not defined specially. 4. The method as same as 2 and 3, measure the frequency FC1 ICC1, ICC2 Circuit current (no signal) The condition is shown as Table 1. Set SW19 to GND (or OPEN) and SW A to side b, measure the current by current meter A. The current is as ICC1 (ICC2). VDC1, VDC2 Output DC voltage Set SW19 to GND (or OPEN), measure the DC voltage of T.P.31 (T.P.28, T.P.25) when there is no signal input. The DC voltage is as VDC1 (or VDC2). C.T.I.1, C.T.I.2 Crosstalk between two input VDC3, VDC4 Output DC voltage Measure the DC voltage of T.P.23 same as note2, the DC voltage is as VDC3 (or VDC4). Vimax1, Vimax2 Maximum allowable input Set SW19 to GND, SG1 as the input signal of Pin 2. Rising up the amplitude of SG1 slowly, read the amplitude of input signal when the output waveform is distorted. The amplitude is as Vimax1. And measure Vimax1 when SG2 as the input signal of Pin 5, Pin 7 in same way. Next, set SW to OPEN, measure Vimax2 when SG2 as the input signal of Pin11, 13, 16. GV1, GV1, GV2, GV2 1. The condition is shown as Table. 2. Set SW19 to GND, SG2 as the input signal of Pin 2. At this time, read the amplitude output from T.P 31. The amplitude is as VOR1. 3. Voltage gain GV1 is GV1= 20 LOG VOR1 [VP-P] 0.7 [VP-P] C.T.I.2= 20 LOG [dB] 1. The condition is shown as Table. This test is by active prove. 2. Set SW19 to GND, SG3 as the input signal of Pin 2. Measure the amplitude output from T.P.31. The amplitude is as VOR3. 3. Set SW19 to OPEN, measure the amplitude output from T.P.31. The amplitude is as VOR3'. 4. The crosstalk between two inputs C.T.I.1 is C.T.I.1= 20 LOG VOR3' [VP-P] VOR3 [VP-P] [dB] when input signal to Pin 5, 7. 5. The difference between of each channel frequency characteristic is as FC1. 6. Set SW19 to OPEN, measure FC2, FC2. FC3, FC4 Freq. characteristic By the same way as Note7 measure the FC3, FC4 when SG5 of input signal. FC1= 20 LOG 3. The frequency characteristic FC1 is VOR2 [VP-P] VOR1 [VP-P] [dB]
5. By the same way, measure the crosstalk between two inputs when SG3 as the input signal of Pin 5, Pin 7. 6. Next, set SW19 to OPEN, SG3 as the input signal of Pin 11, measure the amplitude output from T.P.31. Theamplitude is as VOR4. 7. Set SW19 to GND, measure the amplitude output from T.P.31. The amplitude is as VOR4'. 8. The crosstalk between two inputs C.T.I.2 is VOR4' [VP-P] VOR4 [VP-P] [dB]
9. By the same way, measure the crosstalk between channels 4. The method as same as 2 and 3, measure the voltage gain GV1 when SG2 as the input signal of Pin 5, 7. 5. The difference of each channel relative voltage gain is as GV1. 6. Set SW19 to OPEN, measure GV2, GV12 in the same way. GV3, GV4, Voltage gain 1. The condition is shown as table. This test is by active probe. 2. Measure the amplitude output from T.P.23. 3. Measure the GV3, GV4 by the same way as GV1, GV1, GV2, GV2. FC1, FC1, FC2, FC2 1. The condition is shown as table. This test is by active probe. 2. Set SW19 to GND, SG2 as the input signal of Pin 2. Measure the amplitude output from T.P.31. The amplitude is as VOR1. By the same way, measure the output when SG4 is as input signal of Pin 2, the output is as VOR2. C.T.C.1= 20 LOG C.T.C.1, C.T.C.2 Crosstalk between channel 1. The condition is as Table. This test is by active prove. 2. Set SW19 to GND, SG3 as the input signal of Pin 2. Measure the amplitude output from T.P.31. The amplitude is as VOR5. 3. Next, measure T.P.28, T.P.25 in the same state, and the amplitude is as VOG5, VOB5. 4. The crosstalk between channels C.T.C.1 is VOG5 or VOB5 VOR5 [dB] C.T.I.3, C.T.I.4 Crosstalk between two input Set SG4 as the input signal, and then the same method as table, measure C.T.I.3, C.T.I.4. when SG3 as the input signal of Pin 13,16.
4
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH
5. Measure the crosstalk between channels when SG3 is as the input signal of Pin 5, Pin 7. 6. Next, set SW19 to OPEN, SG3 as the input signal of Pin11, measure the amplitude output from T.P.31. The amplitude is as VOR6. 7. Next, measure the amplitude output from T.P.28, T.P.25 in the same state. The amplitude is as VOG6, VOB6. 8. The crosstalk between channels C.T.C.2 is C.T.C.2= 20 LOG VOG6 or VOB6 VOR6 [dB] Vith1, Vith2 Input selectional voltage The condition is as table. Set SW19 to GND (OPEN), increasing gradually the voltage of input terminal from 0V, measure the voltage of input terminal when output terminal is 4.5V. The input voltage is as Vith1 (Vith 2). Trd1, Trd2 Rising delay time Tfd1, Tfd2 Falling delay time The condition is as table. Set SW19 to GND (OPEN), SG7 is as the input signal of input terminal, measure the waveform of output. Rising delay time is as Trd1 (Trd2). Falling delay time is as Tfd1 (Tfd2). Reference to the Fig. as shown below. VoL1, VoL2 Low level output voltage The condition is as Table. Set SW19 to GND (OPEN), input 0V at input terminal. Measure the output voltage, the voltage is as VoL1 (VoL2).
9. By the same way, measure the crosstalk between channels when input signal to Pin13, 16. C.T.C.3, C.T.C.4 Crosstalk between channel Set SG4 as the input signal, and the same method as table, measure C.T.C.3, C.T.C.4. Tr1, Tf1, Tr2, Tf2 Pulse characteristic 1. The condition is as Table. Set SW19 to GND (or OPEN). 2. The rising of 10% to 90% for input pulse is Tri, the falling of 10% to 90% for input pulse is Tfi. 3. Next, the rising of 10% to 90% for output pulse is Tro, the falling of 10% to 90% for output pulse is Tfo. 4. The pulse characteristic Tr1, Tf1 ( Tr2, Tf2 ) is
100% 90%
50% SG7 Trd Tfd
50% Output waveform
Vsth1, Vsth2 Switching selectional voltage 1. The condition is as table. SG1 is as the input signal of Pin 2, Pin5, Pin7, and SG7 is as the input signal of Pin8, Pin9. There is no input at another pins. 2. Input 0V at Pin19, confirm that there are signals output from
10% 0% Tr Tf
Tr1 (Tr2)=(Tro)2 - (Tri)2 Tf1 (Tf2)=(Tfo) 2
(nsec) (nsec)
T.P.19, T.P.20, T.P.23, T.P.25, T.P.28, T.P.31. 3. Increase gradually the voltage of terminal Pin19. Read the voltage when there is no signal output from the terminals listed as above. The voltage is as Vsth1.
(Tfi)2
VoH1, VoH2 High level output voltage The condition is as Table. Set SW19 to GND (OPEN), input 5V at input terminal. Measure the output voltage, the voltage is as VOH1 (VOH2).
4. SG1 as the input signal of Pin11, Pin13, Pin16, and SG7 as the input signal of Pin17, Pin18. There is no input at another pins. 5. Inputs 5V at Pin19, confirm that there is no signal output from T.P.19, T.P.20, T.P.23, T.P.25, T.P.28, T.P.31. 6. Decreasing gradually the voltage of terminal Pin 19. Read the voltage when there are signals output from the terminals listed as above. The voltage is as Vsth2.
5
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH INPUT SIGNAL
SG No. Sine wave (f=60kHz, 0.7VP-P, amplitude variable) SG1 Signals
0.7VP-P(amplitude variable)
SG2 SG3 SG4 SG5
Sine wave (f=1MHz, amplitude 0.7VP-P) Sine wave (f=10MHz, amplitude 0.7VP-P) Sine wave (f=100MHz, amplitude 0.7VP-P) Sine wave (f=250MHz, amplitude 0.7VP-P) Pulse with amplitude 0.7VP-P (f=60kHz, duty80%)
SG6
0.7VP-P
Square wave (Amplitude 5.0VO-P TTL, f=60kHz, duty50%)
5V
SG7
0V
NOTE HOW TO USE THIS IC
1. R, G, B input signal is 0.7VP-P of standard video signal. 2. H, V input is 5.0V TTL type. 3. Input signal with sufficient low inpedance to input terminal. 4. The terminal of H, V output pin are shown as Fig.1. It is possible to reduce rise time by insert the resister between Vcc line and H, V output Pin, but set the value of resister in order that the current is under 7.5mA. Setting the value of R is more than 2k as shown in Fig.1.
5V 1k 5V R
6. Switch (Pin 17) can be changed when this terminal is GND or OPEN When GND : Signal output from input 1 When OPEN : Signal output from input 2 When the switch is being used as Fig.3 0 to 0.5V : Signal output from input 1 2 to 5V : Signal output from input 2 It is not allowable to set voltage higher than VCC.
17
Fig.3
NOTICE OF MAKING PRINTED CIRCUIT BOARD.
Please notice following as shown below. It will maybe cause something oscillation because of the P.C.B. layout of the wide band analog switch. The distance between resister and output pin is as short as possible when insert a output pull-down resister. The capitance of output terminal as small as possible. Set the capitance between Vcc and GND near the pins if possible. Using stable power-source (if possible the separated powersource will be better). It will reduce the oscillation when add a resister that is tens of ohms between output pin and next stage. Assign an area as large as possible for grounding.
1<7.5mA
Fig.1 5. The terminal of R,G,B output pin (Pin 25, 28, 31). It is possible to add a pull-up resister according as drive ability. but set the value of resister in order that the current is under 10mA. Setting the value of R is more than 500 as shown in Fig.2.
5V 1<10mA
50 430 R
Fig.2
6
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH TEST CIRCUIT
A 0.01 a b SWA VCC5V
47
OPEN 0.01 TP35 R 0.01 TP30 G 0.01
0.01
TP27 B
TP25 GOUT (for sync on G) 47 24
TP22 H
TP21 V
SW19
a b c
36
35
34
33
32
31
30
29
28
27
26
25
23
22
21
20
19
M52755FP
1 TP2
2
0.01
3
4 TP5
5
0.01
6 TP7
7 TP8
8 TP9
9
10
11 TP11
12
13 TP13
14
15
16 TP16
17 TP17
18 TP18
47 0.01 0.01 100
47
47 100 0.01 SW13 b a b 100
0.01 SW5 a
100 0.01 SW7 a
100 SW8 ba b ca b
0.01 SW9 SW11 c a
0.01 SW16 a
100 SW17 SW18 ba b ca b c
a SW2
b
b
SG1 SG2 SG3 SG4 SG5 SG6
SG7
Units Resistance : Capacitance : F
7
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH TYPICAL CHARACTERISTICS
THERMAL DERATING (MAXIMUM RATING)
1250
POWER DISSIPATION Pd (mW)
1068 1000
750
500
250
-20
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE Ta (C)
DESCRIPTION OF PIN
Pin No. 1 3 6 Name VCC1 (R) VCC1 (G) VCC1 (B) DC voltage (V ) 5.0 Peripheral circuit of pins - Remarks
800
2 5 7
Input1 (R) Input1 (G) Input1 (B)
1.5
2.2V
Input signal with low impedance.
620
2.59mA
Input pulse between 3V and 5V. 8 9 Input1 (H) Input1 (V) -
3 to 5V
0V
0.2mA
10, 12, 15, 20, GND 26, 29, 34
GND
-
8
MITSUBISHI ICs (Monitor)
M52755FP
WIDE BAND ANALOG SWITCH
DESCRIPTION OF PIN (cont.)
Pin No. Name DC voltage (V ) Peripheral circuit of pins Remarks
800
11 13 16
Input2 (R) Input2 (G) Input2 (B)
1.5
2.2V
Input signal with low impedance.
620
2.59mA
Input pulse between 3V and 5V. 17 18 Input2 (H) Input2 (V) -
3 to 5V
0V
0.2mA
10k 12k
19
Switch
2.6
13k
7.3k
Switch by OPEN and GND.
2.3V
21 22
Output (V) Output (H)
1k
-
Output impedance is built-in.
24 4, 14, 23, 32, 33
VCC (H, V, Switch) NC
5 -
- -
25 27 30 35
Output (Sync onG) Output (B) Output (G) Output (R)
1.15 2.05
50 430 25, 28, 31 50 23 500
Output impedance is built-in.
28 31 36
VCC2 (B) VCC2 (G) VCC2 (R)
5
-
9

▲Up To Search▲

Price & Availability of M52755FP

	To Download M52755FP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .